Logo
Kontakt & Angebot

Cosmetic Pump Manufacturer — Lotion, Serum, Fine Mist and Foamer Pumps

Jarsking manufactures dispensing pumps as part of the container, not as a loose component. Every pump we quote arrives fitted to the bottle it was specified for, in the same color reference, on one lead time, from one supplier who holds the tooling. Tell us the formula and the fill size and we will specify the pump around them.

CONSULT US FOR CUSTOM SOLUTIONS

Start With Two Questions: Dose and Neck Finish

Almost every pump specification resolves to these two answers, and a buyer who arrives with both can be quoted immediately.

Send us your formula and fill size
01

Dose

ONE PRESS ONE DOSE

Dose is how much product leaves the bottle in one press. It is governed by the formula before anything else: a water-thin serum and a body butter behave completely differently through the same mechanism, and a pump sized for one will disappoint on the other.

Get this wrong and the complaint is never that the pump is faulty. It is that the product runs out too fast, or the customer has to press four times.

02

Neck finish

THREAD DIAMETER 24 mm 24 / 410 THREAD FINISH 400 410 415 ≈1 turn ≈1.5 turns ≈2 turns

Neck finish is what the pump physically screws onto. It is written as two numbers, for example 24/410, following the GPI/SPI convention used across the industry.

24
The outside diameter of the thread, in millimeters.
410
The thread finish: 400 has about one turn of thread, 410 about one and a half, and 415 about two on a taller neck.

Once both numbers are fixed, the pump, the collar and the bottle can be specified as one set.

Pump Specification Reference

Output and neck finish for each pump family, using the standard ranges found across the dispensing-pump industry. Use it to locate your formula before you brief us. The output, neck finish and dip tube for your own program are specified per project and confirmed against your formula at the sampling stage.

Cosmetic pump types with industry-standard output per stroke, commonly used neck finishes and typical applications
Pump type Output per stroke Neck finishes commonly used Typically specified for
Serum / treatment pump 0.12–0.25 mlup to 0.3–0.5 ml for richer actives 18/41020/41024/410 Serums, essences, facial oils
Lotion pump 1.0–2.0 ml3.0–4.0 ml for high-output body and hair formats 20/41024/41028/410 Lotions, shampoo, conditioner, body wash
Fine mist sprayer 0.08–0.15 mlper spray 18/41020/41024/410 Toners, setting sprays, body mist
Foamer pump 0.4, 0.8 or 1.5 mlof liquid, delivered as foam 40 mm42/41043/410 Facial cleansers, hand wash
Airless pump 0.1–0.5 mlheld constant as the bottle empties Matched to the airless bottle body Actives, oxidation-sensitive and preservative-reduced formulas
Trigger sprayer 0.20–0.30 ml mini; about 0.8–1.3 ml standardmini and standard triggers 20/41024/41024/41528/40028/410 Salon formats, volume toner, pet and home care

Output bars use a logarithmic scale from 0.05 to 5 ml, because the pump families span a hundredfold range. Lighter segments show the extended range noted under each figure.

Materials and finishes

Pump bodies and shrouds

PP, PE, AS and ABS, color-matched to the bottle they ship with.

Collars and caps

Metallized finishes in chrome, gold, rose gold and brushed, or anodized aluminum.

H

Dip tubes

Cut to the internal height of the specific bottle in the set, not supplied at a generic length.

PCR

Recyclability routes

PCR resin and mono-material construction, specified per project.

Matching the Pump to the Formula

This is where most pump programs are won or lost. Viscosity decides which mechanism will dispense cleanly, and the chemistry of the formula decides whether air exposure matters. If you are unsure where your formula sits, send it to us: we size the pump against the real formula during sampling, not against a category name.

Send us your formula

Viscosity guide, centipoise (cP)

1101001,00010,000100,000 cP Waterabout 1 cP Shampoo, body wash Heavy creams, balms night cream~50,000 shea balm~120,000 Standard lotion pump, up to about 20,000 cP Airless pump, up to about 80,000 cP Jar, from about 50,000 cP

Logarithmic scale. Figures are indicative industry values; the measured viscosity of your own formula decides the specification.

SMALL DOSE

Formula type

Thin, water-based

Toners, essences, light serums

SpecifySerum pumpFine mist sprayer

These formulas move easily and need a small, controlled dose. A high-output pump on a thin serum is expensive waste: the customer gets more active than the application needs, every single press.

Formula type

Emulsions

Lotions, light creams, conditioners

SpecifyLotion pump20/410, 24/410, 28/410

Emulsions sit in the middle of the range and suit a standard lotion pump, the broadest category. Industry guidance reserves standard lotion pumps for products under roughly 20,000 cP; a richer cream above that moves into the next group.

piston no dip tube AIRLESS

Formula type

Thick creams and balms

Night creams, body butters, balms

SpecifyAirless pumpor a jar for the thickest balms

Heavy creams and balms run from about 30,000 cP to well over 100,000 cP, beyond what a dip-tube pump handles well. The correct specification is an airless system, rated in industry guidance to around 80,000 cP, rather than a stronger spring. The very thickest balms belong in a jar.

air liquid FOAM

Formula type

Foaming cleansers

Facial cleansers, hand wash

SpecifyFoamer pump40 mm, 42/410, 43/410

A foamer makes foam mechanically, mixing air with liquid at the pump head, so the formula has to be thin enough to pass the mesh. A formula thickened for a standard pump will usually need reformulating before it will foam.

airair DIP-TUBE PUMP AIRLESS

Formula type

Oxidation-sensitive actives

Vitamin C and retinol serums

SpecifyAirless pump

These are the strongest argument for an airless system. A conventional pump lets air flow back into the bottle to replace each dose; an airless system dispenses without drawing air back in, because a piston rises behind the formula instead.

Pump Types We Manufacture

Every pump below is supplied as part of a matched set: fitted to its bottle, in the same color reference, on one lead time. Choose the family, then open its page for specifications and the sets we make.

Request a quotation
Treatment pumps with gold metallized collars for serum bottles
01

Serum Pumpen

Small, controlled doses for high-value actives, where every press has to be measured.

0.12–0.25 ml18/41020/41024/410
Black lotion pumps with long nozzles and dip tubes
02

Lotionpumpen

The workhorse of skincare and personal care, from facial formats to 500 ml and 700 ml shampoo and body wash bottles.

1.0–2.0 ml20/41024/41028/410
Fine mist sprayers with overcaps in white, black and clear
03

Feinzerstäuber

Sprayers for toners and body mists, and atomizers matched to fragrance bottles.

0.08–0.15 ml18/41020/41024/410
White foamer pumps with wide foaming chambers for cleanser and hand wash bottles
04

Foamer Pumps

Mechanical foaming for cleansers and hand wash, including refillable and airless foaming formats.

0.4–1.5 ml40 mm42/41043/410
White and blue trigger sprayers
05

Trigger Sprayers

Mini and standard triggers, from hair care and room sprays to larger salon, home and pet-care formats.

0.20–1.3 ml20/41024/41028/40028/410
Airless pump heads in white, black and white with a gold metallized collar
06

Airless Systems

Working with an airless system instead? Here the pump and the bottle body are one engineered unit, with a piston in place of a dip tube.

0.1–0.5 mlMatched to the bottle body

Customization

Color is the most common request, and the one with the most detail behind it. Pump shrouds, collars and caps can be matched to the bottle across materials, then frosted, spray-coated, electroplated, finished in anodized aluminum, screen printed or hot stamped.

Discuss your color and finish
MATCHED MATTE aluminumshell BRAND HOT STAMP 7 mm7 mm

Choose a finish

Custom color

Pump, collar and bottle molded to one color reference. Because a pump and a bottle are usually different polymers, a matched set is built from a physical color sample rather than a number alone, which is how the set still reads as one set under store lighting.

Production, 10,000 sets 30 days for custom-color pump heads and caps

Frosted

A matte, soft surface on the pump shroud, collar or bottle. On plastic, a matte printed surface is produced in two stages: printed on a gloss surface, then frosted.

Frosting adds 5–7 days at the sampling stage

Spray-coated

A color coating sprayed over the molded part, for shades and gradients across the pump head, collar and bottle, run on our own spraying lines.

Production, 10,000 sets 30 days for spray-coated pump heads and caps

Electroplated

Metallized finishes in chrome, gold, rose gold and brushed. Electroplating is matched from a physical sample, because the finished result is a property of the process as well as the color.

Production, 10,000 sets 35 days for electroplated caps

Anodized aluminum

An aluminum shell over the collar or cap, anodized in color, for a true metal surface on the closure.

Production, 10,000 sets 45 days for anodized aluminum caps

Screen printing and hot stamping

Logos and copy printed or foil-stamped onto the bottle and shroud. Artwork is built as vector files to the actual product dimensions, with 7 mm clear at the top and bottom of the print area; hot stamping is matched from a physical sample.

Printing on caps adds 3–4 days at the sampling stage
20screen-printing lines
10hot-stamping lines
3spraying lines
4metallized finishes: chrome, gold, rose gold, brushed

What We Need to Get the First Sample Right

Five inputs decide whether the first sample is the right one. Sending them with the brief saves a sampling round.

  1. A physical color sample

    For any custom color. A Pantone reference works where no sample exists; a fully color-matched set is built to a physical sample.

  2. Size and weight targets

    Stated up front, so the first sample is built to the right brief.

  3. Vector artwork

    AI or PDF files, built to the actual product dimensions.

  4. A clear print margin

    7 mm clear at the top and bottom of the print area on each part.

  5. A sample for metal finishes

    Electroplating and hot stamping are matched from a physical sample.

On existing molds

Color, finish and decoration

Color, finish and decoration changes are made on existing tooling, drawn from more than 30,000 ready-to-use molds.

New tooling

A new pump geometry

A genuinely new shape is a tooling project. Our in-house Mold Manufacturing Center builds a steel mold in 35–40 days.

MOQ and Lead Times

One minimum order quantity, and a timeline you can plan a launch around. The figures below are our standard lead times, counted in days, for pumps, caps and the bottles they ship with.

Request a timeline for your project
Minimum order quantity 10,000 units per SKU on existing molds

  • Full-custom tooling

    Quoted per project, for a new shape built to your design.

  • Production files

    Vector artwork in AI or PDF format, plus Pantone references or physical color samples.

  • When the clock starts

    The production timeline runs from receipt of vector artwork and payment.

Timeline by Project Route

How long a program takes depends on how much of it is new. Choose a route to see its standard timeline, before shipping.

OEM: built to your specifications

We manufacture to your designs and specifications. You keep the IP and the control over every detail.

33–65 days, excluding shipping

ODM: proven molds, your colors and branding

Start from more than 30,000 proven molds and customize color, material, finish and branding. It is the faster, lower-cost route to a matched set.

40–60 days, excluding shipping. Add 5 days for a PET or PETG color change.

OBM: a full custom system, co-developed

Design-led development of a complete system, spanning industrial design, structure and color, material and finish. A new steel mold takes 35–40 days.

84–110 days, excluding shipping

Pump and Component Lead Times

Stage by stage, for pumps, caps and the bottles they are matched to. Production figures are for 10,000 sets.

Sampling

Pump and cap samples7–25
Pump head sample, stock color15–18
Pump head sample, specified color15–25
Plastic bottle samples15–20
Glass bottle samples, existing molds3–15
Frosting+5–7
Printing on caps+3–4

Production, 10,000 sets

Pump heads, custom color or spray-coated30
Caps, custom color or spray-coated30
Caps, electroplated35
Caps, anodized aluminum45
Mass production, complete program30–40

Tooling and shipping

New steel mold35–40
Sea freight35–40

Figures are in days. Dashed bars are time added to a stage: frosting adds 5–7 days and printing on caps adds 3–4 days at sampling. A PET or PETG color change adds 5 days. Your quotation confirms the timeline for your specification.

Applications

Our pump systems serve four industries. In each one the formula and the format decide the pump, so every card links to the pump types that fit it best.

  • Skincare daily routine set of pump bottles, jars and droppers
    01

    Beauty and Skincare

    Serums, essences, moisturizers, cleansers and treatment oils. A serum pump meters a fraction of a milliliter; a lotion pump carries the creams.

    Serum pumpsLotion pumpsAirless
  • Fine mist glass perfume bottle with a wood cap
    02

    Fragrance and Perfume

    Eau de parfum, body mists and hair mists, where an even, fine spray and a decorated collar finish the bottle.

    Fine mist sprayersPerfume packaging
  • Gradient plastic shampoo bottles with pumps
    03

    Körperpflege

    Shampoo, conditioner, body wash and hand wash. Higher-output lotion pumps, foamers for cleansers and trigger sprays for larger formats.

    Lotion pumpsSchaummittelTrigger sprays
  • Wellness oil dropper bottle
    04

    Wellness

    Wellness oils, tinctures and topical products, where a measured dose and lot-number traceability both matter.

    Serum pumpsTropfen

Frequently Asked Questions

The questions buyers ask most before they specify a pump. If yours is not here, send it with your formula and we will answer it against the real product.

Ask about your pump
What does 24/410 mean, and can I use a 24/400 pump on a 24/410 bottle?

The first number is the outside diameter of the thread in millimeters; the second is the thread finish. A 400 finish has about one turn of thread, 410 about one and a half turns, and 415 about two turns on a taller neck. They are not interchangeable: a 24/400 closure will not seat correctly on a 24/410 neck, even though both measure 24 mm. This is why we specify the pump and the bottle together.

How much product should my pump dispense?

Industry-standard ranges are 0.12–0.25 ml for serum and treatment pumps, 1.0–2.0 ml for standard lotion pumps, 3.0–4.0 ml for high-output body and hair formats, and 0.08–0.15 ml for fine mist sprayers. The right figure depends on the formula and the application, and we confirm it against your actual formula during sampling.

Can the pump be color-matched to the bottle?

Yes. Pump shrouds, collars and caps can be matched across materials and finished by screen printing, hot stamping, frosting, spray coating, electroplating or anodized aluminum. For a fully matched set we work from a physical color sample, because the bottle and the pump are usually different polymers.

What is your MOQ and lead time for a custom pump set?

MOQ is 10,000 units per SKU on existing molds. Pump and cap sampling takes 7–25 days, and mass production 30–40 days, counted from receipt of vector artwork and payment. Sea freight adds 35–40 days. Full-custom tooling is quoted per project; a new steel mold takes 35–40 days.

Will a standard pump work with a thick cream?

Up to a point. Industry guidance reserves standard lotion pumps for products under roughly 20,000 cP. Heavy creams and balms, from about 30,000 cP upward, suit an airless system, rated to around 80,000 cP; the thickest balms belong in a jar. Send us the formula and we will size the pump against it rather than against the category.

Do I need new tooling for a custom pump?

Not usually. With more than 30,000 ready-to-use molds, most programs are delivered by customizing color, finish and decoration on existing tooling. A genuinely new pump geometry is a tooling project, and our in-house Mold Manufacturing Center builds a steel mold in 35–40 days.

Which certifications do you hold?

Guangzhou Jarsking Packaging Co., Ltd is certified to ISO 9001:2015 for the manufacture of plastic packaging containers for cosmetics, and our Guangzhou facilities are audited under amfori BSCI by SGS, with reports available on request. Material testing is done per product and per material by accredited third-party laboratories, covering REACH SVHC screening, EU heavy-metal limits for packaging, PFAS screening and California Proposition 65 (bisphenol A). Tell us your target market and we will send the reports that cover the item you are quoting; certificate numbers and validity dates are on our certifications page.

More in Caps and Pumps

A complete set needs more than a pump. Explore the closures, caps and droppers that finish the rest of your range, all matched to the same bottles.

PACKAGING FOR GOOD, DESIGNED FOR GROWTH

Wir benötigen eine Mindestbestellmenge von 10.000 Einheiten pro SKU für bestehende Formen.

    Vernetzen Sie sich mit Jarsking!

    Facebook LinkedIn Pinterest Instagram Youtube TikTok X-Twitter
    Jarsking Logo
    Logo

    Melden Sie sich für neue Designs jede Woche an!

      Unternehmen

      Warum Jarsking

      Lösungen

      Latest Design from Jarsking Studio

      Haarpflege-Verpackungsset
      custom-perfume-packaging-knight-artwork

      Guangzhou Zentrale:

      17. Stock, Ostflügel, Gebäude 2,
      Yiyun Tech Innovation Center,
      Nr. 33-13, Jinshi Dritte Straße, Dayuan Straße,
      Baiyun Bezirk, Guangzhou,
      Provinz Guangdong, China

      Büro Dubai

      Büro 10, 24. Stock,
      Der One Tower,
      943 Sheikh Zayed Road,
      Barsha Heights (Al Thanyah First),
      Dubai, Vereinigte Arabische Emirate

      Jetzt Kontakt aufnehmen

      © Copyright 2026 Jarsking Packaging Alle Rechte vorbehalten.

      Angebot anfordern